Finally understand the steps to do phototherapy manicure

In hot weather, girls will start to apply colorful nail polish to manicure, and the most lasting effect is the popular phototherapy manicure. Here are the steps to do phototherapy manicure, let’s learn about it together:
1. Before making nails, be sure to finish the nail base. First, polish the nails/nail surface to grind.
2. Then use the sanding stick that sands the "surface" of the nails to smooth the uneven lines on the surface of your nails. On the one hand, it can make the mirror effect of the subsequent phototherapy more flawless, and on the other hand, it can remove the grease on the nail surface, so that the phototherapy glue and the nail can adhere more firmly.
3. Then, apply a thin layer of bonding agent evenly, put it in the phototherapy machine for 30 seconds and then take it out.
4. Apply pink sequin glue evenly, do a two-thirds gradient, put it in the phototherapy machine for 30 seconds and take it out.
5. Put on the model glue, put it in the phototherapy machine for 50 seconds and take it out. Then use a pin to polish off the protrusions of the sequins and repair the desired nail type according to personal preference, so that the beautiful phototherapy nail is completed.
Note: The glue should be uniform. The binder and the sealant should not be too thick. When glueing, use the pen smoothly and don't apply to the skin. The complete phototherapy nail is completed.
DIY phototherapy manicure steps
Step1: First polish your nails, you can polish them into a shape you like, square or round, and then polish the nail surface. Then apply Dadi glue again, so that the phototherapy glue can be combined with the nail surface well, and the application should be neither thin nor thick.
Step2: Then put the nail polished fingers into the nail roaster and bake for 4-5 minutes, pay attention to the time, if you inadvertently bake it for a long time, it will crack.
Step3: Next, choose a medium-sized brush, and slowly fill the surface of the nail with small glitter powder, spread it as evenly as possible, and then put it in the nail baking machine and bake it for 4 minutes.
Step4: In order to make the nails look more shiny, fill the nail pieces with two large pieces of particles. You can fill in a little more at the forefront of the nails, so that there is a gradual effect, and then put them into the nail baking machine to bake.
Step5: Finally, apply a layer of transparent phototherapy glue to make the nails look shiny and protect the small sequins. Finally, put it in a roasting machine and bake it for 4 minutes. This kind of phototherapy can generally last for one to two months.
The most basic production steps of phototherapy manicure
To remove the dead skin, use the dead skin push to scoop up the dead skin on the finger, and use the dead skin scissors to cut off the shoveled dead skin. (Exfoliating the dead skin is a key part of doing phototherapy nails. If the dead skin is not removed cleanly, the finished phototherapy nails will tend to curl up)
Manicure, manicure has two parts to be repaired. One is to polish the surface of the nail. The surface of human nails is smooth and oily. It must be polished quickly, or the phototherapy nail will not stick firmly. The second is to shorten the front edge of the nail and use a sanding strip to shape the front edge of the nail into an arc that matches the front edge of the paper holder.
After grinding, use a dusting brush to remove dust, and apply a certain amount of cleaning fluid to a cotton pad to clean the surface of the nails.
Take a small amount of phototherapy primer and apply it on the surface of the nail that has been carved and polished. After applying the primer for 3 minutes
Apply phototherapy gel and take appropriate amount of phototherapy gel with a phototherapy pen. Apply on the nail to make the shape and length that need to be made, put it in the phototherapy lamp and illuminate it for 3 minutes, and then cure.
Repeat step 4 and apply the phototherapy gel twice to make it harder to fall off.
Apply a non-washable sealant, take a small amount of sealant and apply it to the nail surface that has been carved and polished, and illuminate it for 3 minutes. This completes the phototherapy gel.
Be careful not to injure your fingers when repairing. It is best to light up the lamp for more than 3 minutes, preferably 3 minutes.
Simple phototherapy manicure steps
First, use finger pliers and sand sticks to remove the dead skin and then clean the nails, so that the nails can be painted well, and then apply a layer of primer to make the nails more shiny.
Take out the prepared nail polish, first shake the nail polish bottle gently to make the nail polish inside to be more even, so that the color is better, and then brush the nails to color. It takes one action to make the nails look light and translucent. Then apply the nail polish colors in sequence.
After applying the color, apply a layer of transparent nail polish to make the nails more shiny and translucent.
After the clear nail polish is applied evenly, put the finger part into the nail phototherapy machine for two to three minutes to bake to make the nail more colored.
After the three-minute baking is over, gently wipe the nails and the edges of the nails with nail essence oil to prevent the nails from becoming dry and cracked.
After applying the essential oil, let it dry naturally, and then lightly touch the nail polish with a transparent nail polish to form a drop-like shape.
Put your finger into the nail phototherapy machine and bake it, it's still two to three minutes.

In the end, you only need to apply a layer of nail polish essential oil to protect the delicate finger skin and brighten the luster of the nail polish.